Welcome to visit us!

[email protected]

k factor stainless steel 316

SheetMetal.Me – KFactorKFactor Chart. A KFactor will typically range between 0 and .5 for standard materials and thicknesses though smaller and larger KFactors are possible. To help you begin I’ve included a KFactor Chart below which contains common KFactor starting points, good for general fabrication, for steel, aluminum and stainless steel.Bend Angles 183; Gauge Chart 183; Tooling Terminology 183; Bend Allowance 183; Bend Deduction

Whatever your requirements about k factor stainless steel 316, you 'll find the perfect service-oriented solution to match your specific needs with our help. We are here for your questions anytime 24/7, welcome your consultation.

Online Chat [email protected]
  • Bend Radii and K factors for 304 Stainless Steel Sheet

    Mar 09, 2018 · So we bend a lot of mild steel. Our bend radius rule of thumb is the minimum radius = material thickness. We bend lots of stainless, which in terms of hardness, is very similar to mild steel (a36/gr50/cq) If I were to start folding, I would use .125 and a K factor of .45

    Read More
  • K factors, Y factors, and press brake bending precision

    Mar 07, 2018 · For instance, 304 stainless steel forms a radius 20 to 22 percent of the die width, while a radius in 5052 H32 aluminum forms at 13 to 15 percent of the width. The general rule here is thisThe softer the material, the tighter the inside radius. The K factor is defined mathematically as t/Mt, where t is the neutral axis location and Mt is

    Read More
  • Engineering FAQ Fastenal

    What is the difference between 18 8 stainless steel and 316 stainless steel? The 316 stainless steels have 2 3% molybdenum added while the 18 8 series stainless steels do not. While it has comparable strength characteristics, 316 and 316L stainless steel have a higher degree of corrosion resistance due to the addition of the element molybdenum.

    Read More
  • K value for SS fasteners into Alum Mechanical

    Oct 23, 2008 · We use stainless steel fasteners in aluminium structures on system that are mounted in aircraft that fly at low altitude over the sea. We have not had problems with corrosion. k is the nut factor in the traditional rule of thumb equation T = kDF where T is torque, k is nut factor (essentially friction), D is thread major diameter, and F is

    Read More
  • AISI 316 Stainless SteelSpecification and Datasheet

    In comparison, the SS AISI 316 boasts better resistance to chloride rich conditions than the typical SS 304 thanks to the molybdenum addition. Uses for SS AISI 316. Also known as surgical stainless steel, marine steel, 316S16 (as per the British Standard), the SS 316 is an austenitic chromium nickel alloy. As a consequence it:

    Read More
  • Determining the K Factor for Sheet Metal CR4 Discussion

    Dec 05, 2008 · ReDetermining the K Factor for Sheet Metal 12/05/2008 9:46 AM Thanks for the info guys, I had found a lot of the same websites during my own search but get tripped up by the K factor portion of the equation.

    Read More
  • Thermal Conductivity of selected Materials and Gases

    Conductive Heat Transfer through a Stainless Steel Pot Wall with thickness 2 mm temperature difference 80 o C. Thermal conductivity for stainless steel is 17 W/(m K) (from the table above). Conductive heat transfer per unit area can be calculated as. q / A = [(17 W/(m K

    Read More
  • 1/4" x 50' 7x19 316 Stainless Steel Aircraft Cable

    Material316 Stainless Steel; NoteBreaking strength ratings are listed for comparison purposes only. Actual operating loads may vary, but should not exceed the recommended design factor of 20% of the product's breaking strength.

    Read More
  • K Factor Stainless Steel, K Factor Stainless Steel

    offers 20 k factor stainless steel products. About 5% of these are sheet metal fabrication. A wide variety of k factor stainless steel options are available to you,

    Read More
  • K Factor Stainless Steel, K Factor Stainless Steel

    offers 20 k factor stainless steel products. About 5% of these are sheet metal fabrication. A wide variety of k factor stainless steel options are available to you,

    Read More
  • Stainless Steel Grade 316 (UNS S31600)

    Sep 13, 2001 · The 316 family is a group of austenitic stainless steels with superior corrosion resistance to 304 stainless steels. They also have excellent toughness and can be used in the food, marine, chemical and architectural fields. Other applications include fasteners and

    Read More
  • Roughness & Surface Coefficients Engineering ToolBox

    Surface coefficients to calculate flow friction and major pressure loss surfaces like concrete, galvanized steel, corroded steel and more Sponsored Links For turbulent flow the friction coefficient depends on the Reynolds Number and the roughness of the duct or pipe wall.

    Read More
  • Stainless Steel 304 Lenntech

    Material Notes. Type 304 stainless steel is a T 300 Series Stainless Steel austenitic.It has a minimum of 18% chromium and 8% nickel, combined with a maximum of 0.08% carbon. It is defined as a Chromium Nickel austenitic alloy.. Grade 304 is the standard "18/8" stainless that you will probably see in your pans and cookery tools.

    Read More

What Can I Do For You?

Hot Products

Steel Materials

New Products

Copyright © 2015.BTN STEEL Co., ltd. All rights reserved.